Sheet bending

A bent part quotedfrom its flat and its bend lines.

The customer uploads a bent STEP model or a DXF flat pattern. The engine unfolds the part, reads the bend lines and prices the cut on the laser and the bending on your press brake, at your rates.

  • STEP, IGES, DXF and PDF
  • Direction and angle from the customer
  • The flat as a DXF for the shop
  • A calibration list of its own

channel-2mm.step

Flat
211.7 × 60
Bends
2
Strokes
2
Net price · 20 pcs€5.72Instant

Example data: S235 2 mm, 6 kW laser at €95.00/h, press brake at €70.00/h.

01The quote's route

From the file to the technologist

  1. File

    A bent 3D model, or a DXF or PDF flat pattern. For a flat pattern the customer states the thickness.

    STEP · IGES · DXF · PDF
  2. The flat

    A model is unfolded; from a DXF flat the bend lines and the notes beside them are read.

    K-factor
  3. Lines

    Each line's direction and angle: from the file, from the customer in the widget, or from a technologist.

    up · down · angle
  4. Laser and press

    The flat is cut, then bent on the cheapest press brake that takes it.

    your rates
  5. Safety gates

    Short flanges, holes near a line, lines left open, the price threshold.

    Instant priceTo a technologist
  6. To a technologist: Technologist

    Checks the bend lines in the table and on the model, approves or corrects the price.

  7. Price

    The customer sees the net amount and can order.

With no press brake in the park the engine does not price bending: a bent part waits for a technologist, as before.

02The flat

From a solid to a flat blank

A bent model has a constant thickness. The engine unfolds it to a flat blank, measures every bend and prices the flat like a part cut from sheet.

The part from its end

channel-2mm.step

The flat
↑ 90° R3↑ 90° R3
Flat [mm]
211.7 × 60
Bends
2 up, up
Strokes
2
Turning the part over
0
Cut length [mm]
594
Pierces
3
Net price · 20 pcs
€5.72
  • K-factor: yours from the price list, or the DIN 6935 values for each radius.
  • Bends in opposite directions turn the part over between strokes. The offset is turned once, the channel not at all.
  • A model with no radii, up to 6 mm thick, is unfolded at radius 0 and always waits for a technologist.
  • A solid that cannot be unfolded waits for a technologist with a reason.

Example data: flats and prices calculated by the engine on these models.

03Bend lines

A DXF flat and what the customer says

In a flat pattern a bend line lies on a bend layer or is drawn in a broken line type. A note beside the line gives the direction, the angle and the radius. What the file leaves out, the customer fills in in the widget.

bracket-flat.dxf
What was read
Bend 1, 120 mmdashed linenothing
Bend 2, 120 mmIV_BEND layer↑ 90° R3

Bends

Direction and angle of each bend line

All bends90° up90° down
  • Bend 1, 120 mmDirectionDownAngle [°]90
  • Bend 2, 120 mmDirectionUpAngle [°]90
Net price · 20 pcs€6.44

The technologist sees

Nothing to check: the customer gets the price at once.

  • Direction and angle for every line at once: one click.
  • Lines left open do not block the quote. The price takes 90°, and the quote waits for a technologist.
  • The customer can draw a line on a flat part or take away a line that is not a bend. Such a quote waits for a technologist too.
  • A flat in a vector PDF is read the same way and always waits for a technologist.

Example data: a DXF written by the script and read by the engine's reader.

04Price

Bending as an operation after the cut

A bent part's price is the price of the cut flat plus the bending. Bending is counted from the strokes on the press, turning the part over and handling. Setup and the bending program come once per order line.

€10.31 per piece

  • Material4%
  • Cutting with setup54%
  • Bending per piece5%
  • Bending setup and program37%
Strokes
2
Turning the part over
0
Operators
1
  • A heavy or long part is bent by two operators, and the time is paid for each. You set the limits in the price list.
  • Each further radius is a further tool station and a longer setup.
  • A press too short or too weak, or a part too heavy for it: then the press refuses, and the reason gives its figure.

Example data: the channel from chapter 2, shares of the price per piece, rounded to a per cent.

05Blanks

A press brake with no laser in the park

A shop with no cutting machine bends blanks from elsewhere: delivered by the customer or bought cut. When you offer both, the customer chooses in the widget.

Laser and press brake

You cut and bend in the shop.

  • Material
  • Cutting
  • Bending
Net price · 20 pcs€6.44

The customer's blank

The customer delivers the cut blanks with the order.

  • Bending

The customer seesI supply the cut partsYou deliver them cut; the price covers the bending

Net price · 20 pcs€2.64

A blank bought cut

You buy the blanks from a supplier: a price per metre of cut and per pierce, the metal per kg.

  • The supplier's blank
  • Bending

The customer seesCutting includedThe shop provides the cut parts; they are in the price

Net price · 20 pcs€4.89

A customer's blank for a part whose flat the engine developed from a 3D model waits for a technologist: the customer cuts it from their own flat.

Example data: the DXF flat from chapter 3 in three parks.

06Safety gates

What holds a quote, and what refuses it

A part that cannot safely be bent on your press brake does not get a price at once. Each reason on the quote screen tells the technologist what to check.

A 4 mm flange on 2 mm sheet.

Priced, waiting for a technologist
On the quote screen

A flange is shorter than the usual minimum for this thickness. Check it against your dies.

bend_flange_too_short

The engine does not simulate the flanges hitting the tool. A narrow channel or flanges on several sides hold the quote and do not refuse it.

Example data: models written by the script and priced by the engine.

07Panel

What the technologist gets in the panel

The bends table

Each line's length, direction, angle and radius. The customer's value stays beside it, struck through once changed.

Lines on the model

A click on a line shows its angle and direction. The folded view is a preview: no price reads it.

The flat as a DXF

A file to download from the quote screen and through the API: outline, holes, lines with direction, angle and radius. The customer does not get it.

Your press brake

Bending length, force, V dies, part mass. Pick the press from the machine catalogue or type it in.

Calibration on your prices

Approved prices of bent parts go on a list of their own, “Press brake”. Calibration fits the bending multiplier and the setup, and the cut stays with the sheet-cutting list.

Deviation before17.1%
After calibration1.4%

Fitted: bending multiplier 1.23, setup 30 min.

Example data: 6 parts at 3 quantities, the shop's prices rounded to whole units.

08Questions

What shops with a press brake ask

Will adding a press brake change the prices of my flat parts?

No. A flat part with no bend lines never reaches a press brake and is priced as before.

Which files does bending quoting take?

A bent STEP or IGES model, a DXF flat pattern and a flat pattern in a vector PDF. DWG and scans are not read. A bend line can also be drawn on a flat DXF or a flat STEP.

How does the engine know which way a line bends?

From the 3D model, from the layer name or from the note beside the line in a DXF. Where the file does not say, the customer chooses the direction in the widget, and if they do not, the quote waits for a technologist.

Does the engine check for collisions in bending?

No. A narrow channel and flanges on several sides hold the quote for a technologist. The bend sequence and the choice of tools are for the shop to judge.

Can I quote bending without a laser?

Yes. A press brake with no cutting machine bends the customer's blanks or blanks bought cut from a supplier, at your supplier list.

Does the customer get the flat pattern file?

No. Only the shop downloads the flat as a DXF: in the panel or through the API. The file states the K-factor and radii it was developed with.

Add your press brake and check the prices on your own files

Create an account with no card, pick the press from the catalogue, type the rate and upload a bent part you have already quoted.