Tubes and profiles

A tube quotedfrom its section, its cuts and the bar.

The customer uploads a STEP model of a tube or a profile. The engine reads the section, the ends and the holes, and prices the cut on the tube laser, the metal from the bar and the bends on the bender, at your rates.

  • Tubes and open sections
  • The LRA bends table
  • The bar and its waste in the price
  • Two calibration lists

tube-48x3.step

Section
48.3 × 3
Length [mm]
600
Cut length [mm]
429
Pierces
6
Net price · 20 pcs€7.06Instant

Example data: S235, 3 kW tube laser at €110.00/h, tube bender at €70.00/h.

01The quote's route

From the file to the technologist

  1. File

    A 3D model of a tube, an open section or a bent round tube.

    STEP · IGES
  2. Section

    Shape, size and wall. The ends and holes read off the surfaces and checked through sections.

    tube · profile
  3. Tube laser

    Cutting, pierces, moves along the tube and turns. The metal from the bar, with its waste.

    your rates
  4. Bender

    Bends from the LRA table, mandrel and wiper from the tooling chart, die changes.

    rotary draw
  5. Safety gates

    Mitres with no bevel head, a tight radius, a section not in stock, the price threshold.

    Instant priceTo a technologist
  6. To a technologist: Technologist

    Checks the section, the cuts and the bends table, approves or corrects the price.

  7. Price

    The customer sees the net amount, the tolerances and the cutting notes, and can order.

With no tube laser and no bender in the park the engine does not price tubes: a tube waits for a technologist, as before.

02Sections

Seven sections, each one recognised

The engine reads the section off the solid: shape, size and wall. An open section with the marks of a rolled one goes on the tube laser; one that may also be a bent sheet waits for the process to be chosen.

  • Round tube

    48.3x3

    Tube laser
  • Rectangular tube

    60x40x3

    Tube laser
  • Angle

    L 50x50x5

    rolled sectionTube laser
  • Channel

    U 100x50x8.5

    rolled sectionTube laser
  • Tee

    T 60x60x7

    rolled sectionTube laser
  • I or H beam

    I 100x55x5.7

    rolled sectionTube laser
  • Zed

    Z 76x60x4

    a section or a bent sheetProcess to choose
  • A tee and a beam are always rolled. An angle, a channel and a zed with a root radius, a tapered flange or a flange thicker than the web are too.
  • Where the park has a tube laser, a press brake and a sheet cutter, the customer chooses in the widget: cut from a section or bent from sheet.
  • A short round tube with no cuts stays on the lathe: it is a sleeve, not a tube.
  • Cuts that cannot be checked through sections are refused by the tube laser, and a technologist sets the price.

Example data: sections written by the script and read by the engine.

03Cuts

Ends, holes and a mitre

The laser's time is cutting the contours, the pierces and the moves: along the tube and the turn of the chuck. A mitred end needs a bevel head.

tube-48x3.step

Cut length [mm]
429
Pierces
6
Bevel head
no

Laser time, share

Cutting
Pierces
Moves and turns
Net price · 20 pcs€7.06Instant price
  • A hole through the tube is a contour in every wall it crosses.
  • You state the bevel head on the machine: not stated, yes with an angle limit, or no. Not stated, every mitre is checked by a technologist.
  • A narrow web between cuts and a hole small for the wall hold the quote too.

Example data: the same tube as in chapter 1, time as shares of the longest variant.

04The bar

The bar, the gap and the end that cannot be used

The laser cuts tubes from a bar. The chucks leave an end that cannot be used, and there is a gap between the parts. The engine works out how many parts fit on a bar and how many bars the order takes.

6,000 mm bar: 9 parts, 5 mm gap, 200 mm unusable end
Length, gap and a share of the end€7.06per piece
Whole bars€8.78per piece · bars: 3
  • You choose how the metal is charged in the price list: the length with the gap and a share of the end, or whole bars.
  • With whole bars a small order pays for a whole bar, and the difference shrinks with the quantity.
  • Stocked sections are listed with the material: shape, size, wall, a price per kg or per metre, and bar lengths.

Example data: the tube with holes from chapter 3 at three quantities.

05Tube bending

A bent tube as an LRA table

From the tube's centre line the engine reads the bends in the order a bender makes them: the straight before the bend, the turn of its plane, the angle and the radius. Mandrel and wiper come from the tooling chart.

bent-tube-30x2.stepTube 30 × 2
Bends
#Straight before [mm]Rotation [°]Angle [°]Radius [mm]MandrelWiperOutside wall [mm]
115009060RP1none1.6 (−20%)
2120904560RP1none1.6 (−20%)

Straight after the last bend: 140 mm

Net price · 20 pcs€9.07Instant

The same file in a park with no bender: the tube laser does not take it, and the reason says why.

A bent tube, and no tube bender in your price list takes it.

  • Priced as rotary draw bending of round tube. Roll and freeform bending are not priced.
  • A tight radius, a short straight between bends or at the clamp, and a hole near a bend hold the quote.
  • A bender with no tube laser takes a sawn length when the tube has square ends only.
  • A bent rectangular tube is priced and always waits for a technologist.

Example data: a tube built from this LRA table and read back by the engine.

06Safety gates

What holds a quote, and what refuses it

A tube the laser or the bender cannot surely make does not get a price at once. A machine that cannot take it refuses with its own figure in the reason.

A mitred end

A 45° mitre, and the machine states no bevel head.

Priced, waiting for a technologist
On the quote screen

A cut is not square to the tube, as on a mitre. Check the machine has a bevel head.

tube_bevel_check

Example data: models written by the script and priced by the engine.

07Panel

What the technologist gets in the panel

The cut plan

One bar as the price assumes it: the parts, the gaps and the end.

The bends table

Straight before the bend, rotation, angle, radius, mandrel, wiper and the outside wall after bending.

The process from the customer

Where a part can be made more than one way, the customer chooses in the widget. Nothing is selected in advance.

Tolerances on the quote

Cut tolerance, bend tolerance and cutting notes in the widget's summary and on the PDF quote.

Two calibration lists

The tube laser fits the tube cutting multiplier and the setup, the bender the tube bending multiplier and the die change. Each list has its own parts and moves no other technology's prices.

08Questions

What shops with a tube laser ask

Will adding a tube laser change the prices of my milled parts?

No. A part that is not a tube or a profile never reaches a tube laser and is priced as before.

Which sections does the engine recognise?

Round, square and rectangular tube, angle, channel, tee, I or H beam and zed. A section with two webs is not read as a section.

Where does the engine get the order of the bends?

From the tube's centre line in the 3D model: the straights, turns, angles and radii in the order a bender makes them. The table is not edited by hand.

Do you quote bending of rectangular tube?

Yes, where the tube's centre line was read and the park has a bender: as a length and its bends, with no mandrel. Such a quote always waits for a technologist.

Can I bend without a tube laser?

Yes, if the tube has square ends only: the bender takes a sawn length. A tube with other cuts needs a tube laser.

How does the engine know my dies and mandrels?

From the die sets listed on the bender: diameter, radius, mandrels and wiper. A missing set is charged once per order line and holds the quote.

Add your tube laser and check the prices on your own files

Create an account with no card, pick the machine from the catalogue, type the rate and upload a tube you have already quoted.