Milling and turning

Milling and turning quotes,read off the 3D model.

A customer uploads a STEP or IGES. The engine reads holes, threads, pockets and the directions they open to, picks the machine and the blank, and prices the part on your park and your rates. Your engineer approves whatever the safety gates stop.

  • STEP, IGES and assemblies
  • Mills, lathes, mill-turn, Swiss-type
  • Threads and fits confirmed by the customer
  • Calibration on your prices
bracket-150.step
Holes
7
Threads
3
Pockets
2
Setups
2
Machine3-axis mill27.3 min · per piece
Net price · 20 pcs€64.43Instant

Example data: aluminium 6061, 3-axis mill at €70.00/h, aluminium at €5.50/kg.

01Quote path

From the model to your engineer

  1. File

    A 3D model, one part or an assembly. A PDF drawing is read too, and always waits for a person.

    STEP · IGES · PDF
  2. Reading

    Holes and their depths, thread sizes, pockets, inside corners, the directions features open to.

    geometry readout
  3. Machine

    Every machine in your park that can make the part. The one with the lowest machine time and setup at this quantity.

    your park
  4. Time and blank

    Roughing, pockets, drilling, finishing, tapping. The blank from bar or plate sizes you can buy.

    your rates
  5. Safety gates

    Deep holes, thin walls, gears, castings, a part no machine takes, the amount threshold.

    Price at onceTo the engineer
  6. To the engineer: Engineer

    Approves or corrects the price. An approved price becomes a calibration sample.

  7. Price

    The customer sees the net amount for their quantity, the tolerances and threads chosen, and can order.

You set the mode of the safety gates under Quoting rules. A new account starts by reviewing every quote.

02Reading

What the engine reads off the model

Each feature of this bracket, as the engine reads it, and what that reading does to the quote.

Hidden lines: the hole drilled from the side.

4 through holes Ø8

Four holes of one diameter, through 30 mm: one drill, four cycles.

A hole is counted because it is a circle, whatever its size. The customer can give these holes a fit, for example H7.

Where the machine time goes

  • Roughing14%
  • Pockets2%
  • Drilling29%
  • Finishing41%
  • Tapping15%

Blank: aluminium plate 40 × 96 × 156 mm, cut to size

  • The panel shows the same readout beside the 3D preview, and a hole on the model lights its row.
  • Nothing depends on how the part lies in the file: directions are read in the part's own axes.
  • An assembly is read part by part, and each part is priced on its own.

Example data: 20 pcs, aluminium 6061, threads M6 and M8 confirmed.

03Setups

Three axes or five

A bracket with holes in three faces, on a park with both mills. The 3-axis mill clamps it three times, the 5-axis mill once at a higher rate. Which one takes the quote depends on the quantity.

Quantity

3-axis mill

Chosen

Setups: 3

Machine time / pc
€32.36
Setup / pc
€27.09
Piece price on this mill
€111.50

5-axis mill

Setups: 1

Machine time / pc
€41.54
Setup / pc
€16.54
Piece price on this mill
€120.39
  • Every machine that can make the part competes. The quote goes to the one where the piece comes out cheapest: machine time, setup, programming and first-article inspection, each at that machine's rate.
  • A 3-axis mill reaches one direction per setup, a 5-axis mill about five. The setups multiply the setup time and the handling per piece.
  • Your engineer can pin one quote to one machine of the park in the panel. The widget never chooses a machine.

Example data: aluminium 6061, net piece prices. Both mills set to your own rates in the price list.

04Turning

One shaft, five machines

A round part goes to whatever in your park can turn it. Each card is the shaft priced with only that machine in the park.

Ø40 × 120 mmtapped hole at each end: M10 and M8Blank: bar Ø48 × 126 mm
  • Lathe

    With no counter-spindle, the second end is turned in a second chucking.

    Setups
    2
    Net price / pc
    €34.92
  • Lathe with counter-spindle

    The counter-spindle takes the part over and finishes the second end.

    Setups
    1
    Net price / pc
    €37.07
  • Mill-turn centre

    Turns and mills in one chucking, so features off the axis need no second machine.

    Setups
    1
    Net price / pc
    €42.50
  • 5-axis mill

    A mill with a rotary axis takes a round part.

    Setups
    1
    Net price / pc
    €56.48
  • 3-axis mill

    It takes discs only. The shaft is refused, and the panel says why, with the part's figure.

    On the quote screenA round part longer than half its diameter is lathe work - a mill with no rotary axis takes only discs (length up to 0.5 × diameter). A lathe or a 4- or 5-axis mill can price it.Length / diameter: 3.0

Example data: 50 pcs, steel S235, threads confirmed. A park usually has several of these, and the engine picks among them.

05Blank

Cut to size or off the shelf

Both ways of buying the blank are priced, and the cheaper one is taken for the quantity ordered.

Round bar

Round bar

Part Ø40 × 120 mmØ48 × 126 mm

Quantity
  • Cut to size€206.42Cheaper
  • Catalogue stock€213.73

Plate

Plate

Part 30 × 90 × 150 mm

  • Cut to size40 thk × 96 × 156 mm€64.43Cheaper
  • Catalogue stock40 thk × 100 × 156 mm€65.51

A catalogue plate is a little wider, and the surplus is milled off: more metal and more machine time.

  • Bar and plate sizes come from the series a stockist sells. The blank is the next size up with an allowance.
  • Sawn to length, the supplier charges a cut per piece. Bought in stock lengths, you pay for the surplus.
  • You can fix one way in the price list for every quote, and your engineer can change it for one quote.

Example data: shaft in steel S235, bracket in aluminium 6061 at 20 pcs.

06Quality

Tolerances, finish and fits

The same bracket, priced again with one choice changed. The difference is the extra machine and inspection time.

ISO 2768-1 m, Ra 3.2€64.43
ISO 2768-1 c€63.57−€0.86
ISO 2768-1 f€70.77+€6.34
Ra 1.6€66.60+€2.17
H7 fit in 4 holes€73.53+€9.10
3 surfaces held to class f€78.08+€13.65

Example data: 20 pcs, aluminium 6061, net price per piece.

Chosen by the customer

In the widget the customer picks the general tolerance and the finish, ticks threads and fits on the 3D model, and can hold single surfaces tighter. Each choice reprices the part at once.

Holes and threads on the 3D model are clickable - a click ticks or unticks a thread or a fit.

07Stops

Parts the engine does not price on its own

Six parts, each built as a model and run through the engine. Two are refused, four are priced and held for your engineer.

No machine takes itPriced, waits for the engineer

Plate 560 × 540 mm

No machine takes it

Too big for both mills in Y. The reason names each machine with its own travel, so a field typed wrong shows at once.

The engineer seesPart dimensions exceed the machine work envelope.3-axis mill · Part size: 540 mm, max 500 mm (Y axis)5-axis mill · Part size: 540 mm, max 500 mm (Y axis)
part_exceeds_envelope

Each part was priced on an example park of a 3-axis mill, a 5-axis mill and a lathe.

08Panel

What your engineer sees

  • The model and its readout

    Holes, threads and pockets on the 3D preview, each linked to its row.

  • The cost, term by term

    Material, machine time per operation, setup, programming, inspection.

  • Similar parts

    Parts the shop has already approved, with their prices.

  • One field for the price

    A corrected price is kept beside the engine's and becomes a calibration sample.

app.metronq.com/quotes/9f2a4c1e
Quotes
Documentation ↗Find a parameter, e.g. margin, setup+ New quote2EN

← Quotes WID-1125

WID-1125
Awaiting reviewMillingDownload CAD fileExport quote (PDF)CSV (full)
▾ Why does this need review?
complexity: 4.2 · auto-accept threshold: 6
Quote value exceeds the review threshold.Order value€5,807.75max €3,000.00
kolnierz-120.step

From the widget

ViewDimensionsSectionMeasure

Rotate: left button · Pan: right · Zoom: wheel · Click a feature to select it

Dimensions120 × 120 × 22 mm
Volume215.6 cm³
Mass (Aluminium 6061)582 g
Surface412.6 cm²
Faces34
Holes88× Ø9
Min. wall6.40 mm
Customer specification
Edit parameters
Qty25 pcs
MaterialAluminium 6061 · EN AW-6061
MachineDMU 50
Machine for this jobDMU 50cheapest€231.31 / pcs
StockPlate 25 mm
Blank25 thk × 126 × 126 mm · 1.07 kg · 54% used
How it is boughtCut to size
Dimensional & angular tolerances · ISO 2768-1Medium (m) · ±0.3 mm at 120 mm
Shape & position tolerances · ISO 2768-2K - standard
Surface roughnessRa 3.2 - standard
Threads4 × M8
Finishing operationsZinc plating
Unit priceEngine: €231.31231.31€/pcDiscounte.g. 5%Customer pays (net)€231.31/pc · total €5,807.75NoteRejectApprove and send

Example data, a different part from the bracket above.

The engine learns your prices

Approved prices of machined parts fit two figures of your price list: a rate multiplier and a setup time. A fit runs by itself after each approved or corrected quote. Laser and printing prices have lists of their own.

The engine's price against the approved price

Mean deviation
12.2%
Calibration multiplier
1.00
Setup time [min]
30

Example data: 10 prices approved by the shop.

09Machines

Your park, your rates

  • Mills

    3, 4 and 5 axes

    Axes decide how many setups a part takes; a rotary axis lets a mill take round parts.

    623 models in the catalogue

  • Lathes

    Turning

    Swing, turning length and a counter-spindle, which saves the second chucking.

    62 models in the catalogue

  • Mill-turn

    Driven tools

    Turns and mills in one chucking. Its milling envelope decides which blocks it takes.

    90 models in the catalogue

  • Swiss-type

    Bar-fed, unattended

    A sliding headstock for long slender parts, set up once for long runs.

    53 models in the catalogue

Your tools

List the end mills and inserts a machine holds, and the smallest of them becomes its smallest inside corner. With no list, the typed minimum tool radius is used.

The rest is the shop's

  • Hourly rate and minimum batch per machine
  • Setup time, programming and first-article inspection
  • Materials, their price per kg and the bar and plate sizes you buy
  • Margin, minimum order value and delivery

Picking a model from the catalogue copies what its maker publishes: envelope, axes, spindle. The rate is never copied.

10Questions

Questions from machine shops

Does it quote assemblies?

Yes. A STEP with several parts becomes one quote with a line per part, each priced on its own. A part that looks bought, such as a bearing or a screw, gets no machining price until your engineer decides.

And a PDF drawing?

The engine reads the dimensions, tolerances and material off the drawing and rebuilds the part where it can. A price from a drawing always waits for your engineer.

Where does the machining time come from?

From the features read off the model and the material's removal rates, on the machine chosen. The rates are yours, and calibration fits the result to the prices you approve.

Will it send every part to my 5-axis machine?

No. Every machine that can make the part competes, and the one with the lowest machine time and setup share at the quantity ordered takes the quote. Your engineer can pin a quote to another machine.

Does it price gear cutting, grinding or EDM?

No. A gear is priced without its teeth and held for your engineer. Grinding and EDM are not priced: your engineer adds them to the price.

How are threads and fits priced?

The engine offers a thread where a hole has a tap drill size, and a fit for each hole diameter. Only what the customer or your engineer confirms is priced.

Does the customer see the cost breakdown?

No. The customer sees the net price for their quantity, the tolerances and threads chosen and the delivery time. The breakdown and the reasons a quote stopped are for the shop alone.

I also cut sheet and print. Does that change machining prices?

No. A part a laser can cut or a printer can print is offered that way only where your park has the machine, and where both are possible the customer chooses. Machining prices stay as they are.

Add your machines and upload a part you have quoted

A new account starts by reviewing every quote, so you see the readout, the time and the price before anything reaches a customer.